Solution
Part I Preparing for Live View ShootingPart II Switching the AF Method
Part II-1 Focusing with AF (Face+Tracking)
Part II-2 Focusing with AF (FlexiZone - Multi)
Part II-3 Focusing with AF (FlexiZone - Single)
Part III Focusing with MF (Manual Focus)
Part IV Taking the Picture
General Live View Shooting Cautions
You can shoot while viewing the image on the camera's LCD monitor. This is called "Live View shooting".
This article explains how to change the focus mode during Live View shooting. For details on how to use Live View shooting with the default settings, refer to the related information.
Note that the shooting procedure is slightly different for still photos and movies. To shoot still photos, refer to the instructions for still photos. To shoot movies, refer to the instructions for movies.
Caution
Live View shooting is effective for "still-life" shots, when there is no change in the distance to the subject.
If you handhold the camera and shoot while viewing the LCD monitor, camera shake may cause blurred images. Using a tripod is recommended.
Part I Preparing for Live View Shooting
1. Set the camera's power switch to ⋖ON⋗.
2. To shoot still photos, set the Live View shooting/Movie shooting switch to ⋖⋗. To shoot a movie, set the switch to ⋖
⋗.
When shooting a movie, the image will appear on the LCD monitor.
3. To shoot a still photo, press the ⋖⋗ button. The image will appear on the LCD monitor.
Caution
To shoot still photos, set [Live View shoot.] on the [ ] tab to [Enable]. ([Enable] is selected in default settings.)
To focus on the subject using AF (autofocus), go to Part II. To focus on the subject using MF (manual focus) go toPart III . The procedures in Part II and Part III apply to both still photo shooting and movie shooting.
Part II Switching the AF Method
4. Set the lens's focus mode switch to ⋖AF⋗.
5. Check that the camera is prepared to shoot, and then press the ⋖MENU⋗ button.
6. Use ⋖⋗ to select [AF method] on the [
] tab, and then press the ⋖
⋗ button.
7. Select the AF mode, and then press the ⋖⋗ button.
8. After you press the ⋖MENU⋗ button to close the menu screen, the image will appear on the LCD monitor.
Caution
If you press the ⋖⋗ button while an image is displayed on the LCD monitor, the Quick Control screen, for selecting the AF method and other settings, appears. For details, refer to the user manual.
Proceed to one of the following procedures, depending on which AF method you select.
Part II-1 Focusing with AF (Face+Tracking)
Part II-2 Focusing with AF (FlexiZone - Multi)
Part II-3 Focusing with AF (FlexiZone - Single)
Part II-1 Focusing with AF (Face+Tracking)
With [ +Tracking], the camera detects and focuses on human faces. If a face moves, the AF point ⋖
⋗ also moves to track the face.
9. Focus on the subject's face.
You can also tap on the LCD monitor screen to select the face or subject. If the subject is not a face, [ ] will be displayed.
10. When you press the shutter button halfway, the camera will focus on the [ ] face.
Caution
At this point, the camera has only focused on the subject, and the photo is not yet shot. If you follow the procedure in Part IV, a photo will be shot and the image saved.
Caution
Part II-2 Focusing with AF (FlexiZone - Multi)
[FlexiZone - Multi] makes it easy to focus on moving subjects. You can use up to 35 AF points for wide-area focusing (automatic selection). This wide area can also be divided into 9 zones for focusing (zone selection).
9. Select the zone for the AF frame.
Area frame
10. Aim the AF point over the subject and press the shutter button halfway.
Caution
At this point, the camera has only focused on the subject, and the photo is not yet shot. If you follow the procedure in Part IV, a photo will be shot and the image saved.
Caution
Part II-3 Focusing with AF (FlexiZone - Single)
[FlexiZone - Single] The camera focuses with a single AF point, allowing you to focus on a particular subject.
9. The AF point ⋖⋗ will appear. During movie shooting, if [Movie Servo AF] is set to [Enable], the AF point will be displayed in a larger size.
10. Move the AF point.
11. Aim the AF point over the subject and press the shutter button halfway. (Hold the button at the halfway point.)
Caution
At this point, the camera has only focused on the subject, and the photo is not yet shot. If you follow the procedure in Part IV, a photo will be shot and the image saved.
Part III Focusing with MF (Manual Focus)
You can magnify the image and focus precisely with manual focus.
3. After procedures 1 through 3 in Part I, set the lens's focus mode switch to ⋖MF⋗.
4. Turn the lens focusing ring to focus roughly.
5. Press ⋖⋗, and the magnifying frame will appear.
You can also tap [ ] on the screen to magnify the image.
Magnifying frame
6. Use ⋖⋗ to move the magnifying frame to the position where you want to focus. You can also tap it to move it.
Pressing ⋖⋗ or the ⋖
⋗ button will return the magnifying frame to the screen's center.
7. Press the ⋖⋗ button to magnify the frame.
AE lock
Magnifying frame
Magnification
Each time you press the ⋖⋗ button, the magnification of the image will change in the following sequence:
Normal view -⋗ 1x -⋗ 5x -⋗ 10x -⋗ Normal view
8. While looking at the magnified image, turn the lens focusing ring to focus manually.
9. After achieving focus, press the ⋖⋗ button to return to the normal view and check the composition.
Part IV Taking the Picture
After achieving focus in Part II and Part III, take a picture.
To shoot a still photo, press the shutter button completely.
To shoot a movie, press ⋖⋗.
General Live View Shooting Cautions
Be sure to observe the following cautions during Live View shooting.
Caution
-Under low- or bright-light conditions, the Live View image may not reflect the brightness of the captured image.
-Even if a low ISO speed is set, noise may be noticeable in the displayed Live View image under low light. However, when you shoot, the image recorded will have less noise. (The image quality of the Live View image is different from that of the recorded image.)
-If the light source (illumination) within the image changes, the screen may flicker. If this happens, exit Live View shooting and resume Live View shooting under the actual light source.
-If you point the camera in a different direction, it may throw off the Live View image's correct brightness momentarily. Wait until the brightness level stabilizes before shooting.
-If there is a very bright light source in the image, the bright area may appear black on the LCD monitor. However, the actual captured image will correctly show the bright area.
-In low light, if you set the [ : LCD brightness ] to a bright setting, noise may appear in the Live View image. However, the noise will not be recorded in the captured image.
-When you magnify the image, the image sharpness may look more pronounced than in the actual image.
-During Live View shooting, certain Custom Function settings will not take effect. For details on Custom Function settings, refer to the instruction manual supplied with the camera.
-If the attached lens has an Image Stabilizer and you set the Image Stabilizer (IS) switch to ⋖ON⋗, the Image Stabilizer will operate at all times even if you do not press the shutter button halfway. The Image Stabilizer consumes battery power and may decrease the number of possible shots depending on the shooting conditions. If you use a tripod or if the Image Stabilizer is not necessary, it is recommended to set the IS switch to ⋖OFF⋗.
-The focus preset function is possible for Live View shooting only when using a (super) telephoto lens equipped with the focus preset mode released in and after the second half of 2011.
-FE lock will not work if the built-in flash or an external Speedlite is used. Modeling flash will not work if an external Speedlite is used.
-When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable.
-Shooting in high temperatures may cause noise and irregular colors in the image.
-If Live View shooting is used continuously for a prolonged period, the camera's internal temperature may rise, and image quality may deteriorate. Always exit Live View shooting when you are not shooting.
-If you shoot a long exposure while the camera's internal temperature is high, image quality may deteriorate. Exit Live View shooting and wait a few minutes before shooting again.
-If the camera's internal temperature increases due to prolonged Live View shooting or a high ambient temperature, a white [ ] or red [
] icon will appear.
The white [ ] icon indicates that the image quality of still photos will deteriorate. It is recommended that you temporarily exit Live View shooting and allow the camera to cool down before shooting again.
-The red [ ] icon indicates that the Live View shooting will soon stop automatically. If this happens, you will not be able to shoot again until the camera's internal temperature decreases. Exit the Live View shooting or turn off the power and let the camera rest for a while.
-Using Live View shooting at a high temperature for a prolonged period will cause the [ ] or [
] icon to appear earlier. When you are not shooting, always turn off the camera.
-If the camera's internal temperature is high, the quality of images shot with high ISO speed or long exposure may deteriorate even just before the white [ ] icon is displayed.
-In magnified view, the shutter speed and aperture will be displayed in red. If you take the picture in magnified view, the exposure may not come out as desired. Return to the normal view before taking the picture.
-Even if you take the picture in magnified view, the image area for the normal view will be captured.
-Even when focus is achieved, pressing the shutter button halfway will focus again.
-The image brightness may change during and after the AF operation.
-Depending on the subject or shooting conditions, etc., focusing may take longer or the continuous shooting speed may become slower.
-If the light source (illumination) changes while the Live View image is displayed, the screen may flicker and focusing may be difficult. If this happens, exit Live View shooting and perform AF under the actual light source under which you are shooting.
-If [ +Tracking] is set, magnified view is not possible.
-When [FlexiZone - Multi] is set and you press the ⋖⋗ button (or tap [
] on the screen), the center of the selected zone (or image center with automatic selection) will be magnified. If you press the shutter button halfway, the display will return to normal and the camera will focus.
-When [FlexiZone - Single] is set and you press the ⋖⋗ button (or tap [
] on the screen), the area covered by the AF point will be magnified. Press the shutter button halfway to focus in the magnified view. This is effective when the camera is attached to a tripod and you need to attain very precise focus. If focusing is difficult in magnified view, return to the normal display and use AF. Note that the AF speed differs between the normal and magnified views.
-If you magnify the view after focusing with [FlexiZone - Multi] or [FlexiZone - Single] in the normal view, precise focus may not be achieved.
-In Servo AF mode, when you press the shutter button halfway in the magnified view, the display will return to normal and the camera will focus.