Solution
Has the Power Switch Been Just Turned ON?Is the Telephone Line Connected or Configured Properly?
Is your machine in the Fax mode?
Is the document properly loaded?
Is the one-touch key or coded dialing code registered properly?
Did you dial the correct number?
Is the machine in Sleep mode?
Is the recipient's machine out of paper?
Are there other documents being sent from the memory?
Has an error occurred during a transmission?
Is the telephone line working properly?
Is the recipient's machine a Super G3 fax machine?
Is ⋖Busy/No Signal⋗ shown in the error transmission report?
Did the recipient's machine answer within 35 seconds (after all automatic redialing attempts)?
Is the Processing/Data indicator blinking?
Is the machine overheated?
Add a pause to the number and try to send the fax again.
Slow down the send speed.
Has the Power Switch Been Just Turned ON?
Wait a few moments until the machine starts and warms up.
Is the Telephone Line Connected or Configured Properly?
[ Connecting a Telephone Line (MF4890dw/MF4870dn/MF4750 Only) ]
[ Select Line Type (MF4890dw/MF4870dn/MF4750 Only) ]
Is your machine in the Fax mode?
Press [ ] (FAX) to switch to the Fax mode.
Is the document properly loaded?
Properly load the document.
Is the one-touch key or coded dialing code registered properly?
Check that the Address Book settings are registered correctly.
[ Registering and Editing One-Touch Keys (MF4890dw/MF4870dn/MF4750 Only) ]
[ Registering and Editing Coded Dialing Codes (MF4890dw/MF4870dn/MF4750 Only) ]
Did you dial the correct number?
Check that you have the correct number.
Is the machine in Sleep mode?
Press [ ] (Energy Saver) on the operation panel to exit the Sleep mode.
Is the recipient's machine out of paper?
Ask the recipient to ensure that paper is loaded in the machine.
Are there other documents being sent from the memory?
Wait until the transmission is completed.
Has an error occurred during a transmission?
Is the telephone line working properly?
Make sure there is a dial tone when you press [ ] (Hook) or when you lift the handset of any external telephone connected to the machine. If there is no dial tone, contact your local telephone company.
Is the recipient's machine a Super G3 fax machine?
Make sure the recipient's machine is compatible with your machine.
Is ⋖Busy/No Signal⋗ shown in the error transmission report?
The fax number you dialed is busy. Try sending the document later.
Did the recipient's machine answer within 35 seconds (after all automatic redialing attempts)?
Ask the recipient to check the machine. For an overseas call, add pauses to the registered number.
Is the Processing/Data indicator blinking?
The external phone or the optional handset is busy. Please wait until the external phone is not busy.
Is the machine overheated?
Unplug the machine and let it cool for about 5 minutes. Then plug in the machine and try sending again.
Add a pause to the number and try to send the fax again.
When making an overseas call, you may need to add a pause to the fax number.
Since signals are transmitted over long distances across a complicated channel, your call may not be connected without adding a pause after the country code or in front of the fax number. By adding a pause, enough time elapses before the machine starts dialing the number again.
1. Place your fax.
[ Paper Handling ]
2. Press [ ] (FAX).
3. Specify the scanning settings as needed.
4. Enter the international access code using the numeric keys.
For details about on international access codes, contact your telephone company.
5. Press [ ] (Redial/Pause) to enter a pause as needed.
* The default pause length varies depending on the country where you are using the machine.
6. Enter the country code, the area code, and the fax/telephone number using the numeric keys.
7. Press [ ] (Redial/Pause) to add a pause to the end of the fax/telephone number as needed, and then press [OK].
8. Press [ ] (Start).
Slow down the send speed.
The send start speed is specified 33600 bps in the default setting, however you may not be able to send a fax depending on the status of the recipient fax machine or the line.
Select a slower send speed using following procedure, and then send a fax.
1. Press [ ] (Menu).
2. Press [ ] or [
] to highlight ⋖System Settings⋗, and then press [OK].
If a System Manager PIN is specified
Use the numeric keys to enter the System Manager PIN, and then press [OK].
3. Press [ ] or [
] to highlight ⋖Communication Management Settings⋗, and then press [OK].
4. Press [ ] or [
] to highlight ⋖Fax Settings⋗, and then press [OK].
5. Press [ ] or [
] to highlight ⋖TX Start Speed⋗, and then press [OK].
6. Press [ ] or [
] to highlight the send start speed, and then press [OK].
7. Press [ ] (Menu) to close the Menu screen.
The procedure is complete.