Solution
Before Configuring Wireless SettingsWireless Setup Using WPS (Wi-Fi Protected Setup)
Software Installation
Information
Before Configuring Wireless Settings
Caution
Make sure that the computer and access point or router are connected.
After confirming the connection, perform the following instructions to add (connect) the machine to the network.
A: Internet
B: Access point or wireless router, etc.
- Notes on Wireless Connection
Caution
Wireless Setup Using WPS (Wi-Fi Protected Setup)
Caution
1.
Use the Menu button (A) to select Device settings.
2.
Use the or
button (B) to select LAN settings, then press the OK button.
3.
Select WLAN active/inactive, then press the OK button.
4.
Select Wireless LAN active, then press the OK button.
When wireless connection is enabled, the Wi-Fi lamp (C) lights blue.
5.
Select Wireless LAN setup, then press the OK button.
6.
Select WPS, then press the OK button.
7.
Select Push button method, then press the OK button.
- To use the PIN code method for setup
Select PIN code method in 7, then press the OK button. Follow the on-screen instructions to operate the machine and access point. When the screen in 9 appears, press the OK button.
Caution
8.
Press and hold the WPS button on the access point (for about 5 seconds), then press the OK button on the machine within 2 minutes.
For details on the WPS button pressing, refer to the manual of your access point.
The Wi-Fi lamp (blue) on the machine flashes while searching for or connecting toan access point.
9.
When the above screen appears, press the OK button.
Caution
Software Installation
The procedure is not necessary if the software was installed using the network setup cable.
To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of application software to be installed.)
Caution
Easy-WebPrint EX
Easy-WebPrint EX is Web print software that is installed on the computer when installing the supplied software. Internet Explorer 7 or later (Windows) is required to use this software. An Internet connection is required for installation.
1.
Make sure that any of the lamps on the mode buttons (A) lights and that the Wi-Fi lamp (B) lights blue.
Caution
2.
Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.
The setup program starts automatically.
Caution
3. (Windows 7/Windows Vista)
Windows XP -⋗ 4
Click Run Msetup4.exe on the AutoPlay screen, then click Yes or Continue on the User Account Control dialog box.
If the User Account Control dialog box reappears in following steps, click Yes or Continue.
4.
Select your place of residence, then click Next.
Caution
5.
Select a country or region, then click Next.
6.
Click Easy Install.
The drivers, application software, and on-screen manuals are installed.
Caution
7.
Click Install.
8.
Select Use the printer with wireless LAN connection, then click Next.
Follow any on-screen instructions to proceed with the software installation.
9.
When the Printer Detection screen appears, click Next.
Caution
- Click Cancel and start again from 6, then be sure to select Use the printer with wireless LAN connection in 8.
10.
Make sure that any of the lamps on the mode buttons (A) lights, then click OK.
11.
When the Detected Printers List dialog box appears, select Canon MX410 series, then click Next.
Caution
12.
When the Setup Completion screen appears, click Complete or OK.
Information
1.
Click Next.
Follow any on-screen instructions to proceed with the software installation.
- Important Information for the Installation
If the serial number is not displayed on the registration screen, input the number found inside the machine.
Caution
Caution
The User Registration screen will only be displayed when Europe, Middle East, Africa is selected on the Select Your Place of Residence screen.
If the Extended Survey Program screen appears
If you can agree to Extended Survey Program, click Agree.
If you click Do not agree, the Extended Survey Program will not be installed.
(This has no effect on the machine's functionality.)
2.
Click Exit to complete the installation.
3.
Solution Menu EX starts.
Remove the Setup CD-ROM and keep it in a safe place.
Caution
Caution
In Windows 7 and Windows Vista SP1 or later, the XPS Printer Driver can be installed additionally. To install, perform from 1 in [ Software Installation ]. Click Custom Install in 6, then select XPS Printer Driver in the Custom Install screen.
- Use from Additional Computers
Caution
To use from additional computers
1. Insert the Setup CD-ROM into the computer from which you want to use the machine.
2. Follow the on-screen instructions to install the software.
Other settings are not required.
(A) Computer from which the machine can be used currently
(B) Additional computers on the same network
It enables the computer to use the machine.
Caution