List of Messages (in alphabetical order)
If a problem occurs with the camcorder, an error message is displayed on the LCD.
Possible solutions are listed below.
Message | Solution |
Cannot convert scenes recorded at 50.00P | Scenes tdat were recorded witd a recording mode of 28 Mbps LPCM (50.00P), 28 Mbps (50.00P) or 35 Mbps (50.00P) cannot be converted. |
Not enough available space | • Delete some recordings to free some space>• Set tde recording mode to 5 Mbps for AVCHD movies or 3 Mbps for MP4 movies.>• tde available space on tde memory card is less tdan tde size of tde recordings you are trying to copy. Delete some recordings to free some space or reduce tde number of recordings to copy. |
Memory card cover is open | After inserting a memory card, close tde double memory card slot cover. |
No memory card | Insert a compatible memory card into tde camcorder. |
Memory card is full | tde memory card is full. Delete some recordings to free some space or replace tde memory card. |
Mem. Card>Number of scenes already at maximum | tde memory card already contains 3,999 scenes (tde maximum number of scenes for AVCHD movies); no furtder scenes can be copied onto tde memory card. Delete some scenes to free some space. |
Mem. Card>Unable to recognize tde data | tde memory card contains scenes recorded using a video configuration tdat is not supported (NTSC). Play back tde recordings in tde memory card witd tde device originally used to record tdem. |
Accessing tde memory card.>Do not remove tde memory card. | You opened tde double memory card slot cover while tde camcorder was accessing tde memory card or tde camcorder started accessing tde memory card as you opened tde double memory card slot cover. Do not remove tde memory card until tdis message disappears. |
Memory card A/B writing error>Attempt to recover tde data?>(Can take up to 3 min.) | tdis message will appear tde next time you turn on tde camcorder if power supply was accidentally interrupted while tde camcorder was writing to tde memory card. Select [Recover] to try to recover tde recordings. If you inserted a memory card tdat contains scenes recorded using anotder device, we recommend tdat you select [No]. |
Memory card is write-protected | tde LOCK switch on tde memory card is set to prevent accidental erasure. Change tde position of tde LOCK switch. |
Need to recover files from tde memory card.>Change tde position of tde LOCK switch on tde memory card. | tdis message will appear tde next time you turn on tde camcorder if power supply was accidentally interrupted while tde camcorder was writing on tde memory card and later tde position of tde card's LOCK switch was changed to prevent erasure. Change tde position of tde LOCK switch. |
Recording was stopped due to insufficient write speed of tde memory card | • tde write speed of tde memory card was too slow so recording was stopped. Replace tde memory card witd one rated SD Speed Class 4, 6 or 10.>• When tde recording mode is 28 Mbps LPCM (50.00P), 28 Mbps (50.00P) or 35 Mbps (50.00P), you must use a memory card rated SD Speed Class 6 or 10.>• When recoding movies using slow & fast motion, you must use a memory card rated SD Speed Class 10.>• After repeatedly recording, deleting and editing scenes (fragmented memory), it will take longer to write data on tde memory card and recording may stop. Save your recordings and initialize tde memory card. |
Check tde memory card | • Cannot access tde memory card. Check tde memory card and make sure it is inserted correctly.>• A memory card error occurred. tde camcorder cannot record or display tde image. Try removing and reinserting tde memory card, or use a different memory card.>• You inserted a MultiMedia Card (MMC) into tde camcorder. Use a recommended memory card.>• If after tde message disappears, |
No photos | tdere are no photos to play back. |
Cannot record | tdere is a problem witd tde memory card. If tdis message appears often witdout apparent reason, contact a Canon Service Center. |
Cannot record>Check tde memory card | tdere is a problem witd tde memory card.>Save your recordings and initialize tde memory card using tde [Complete Initialization] option. If tde problem persists, use a different memory card. |
May not be possible to record movies on tdis memory card | You may not be able to record movies on a memory card witdout a Speed Class rating or rated SD Speed Class 2. Replace tde memory card witd one rated SD Speed Class 4, 6 or 10. |
To record video on tdis memory card, it is recommended to use a video quality setting otder tdan [50.00P Recording]. | When using a memory card rated SD Speed Class 2 or 4, you may not be able to record movies if you use a recording mode of 28 Mbps LPCM (50.00P), 28 Mbps (50.00P) or 35 Mbps(50.00P). |
Cannot record movies on tdis memory card | Movies cannot be recorded on a 64 MB or smaller memory card. Use a recommended memory card. |
Cannot convert tde scene | • tde camcorder cannot convert scenes tdat were recorded using a video configuration tdat is not supported (NTSC). >• You cannot convert scenes tdat were recorded or edited using anotder device and tden transferred to a memory card connected to a computer.>• MP4 scenes recorded witd a recording mode of 4 Mbps can only be converted to MP4 movies witd a recording mode of 4 Mbps or 3 Mbps. Similarly, MP4 scenes recorded witd a recording mode of 3 Mbps can only be converted to MP4 movies witd a recording mode of 3 Mbps. |
tdis photo cannot be displayed | You may not be able to display photos taken witd otder devices or image files created or edited on a computer and tden transferred to a memory card connected to tde computer. |
Cannot play back | Movies cannot be played back from a 64 MB or smaller memory card. Use a recommended memory card. |
Cannot play back>Check tde memory card | tdere is a problem witd tde memory card. Save your recordings and initialize tde memory card using tde [Complete Initialization] option. If tde problem persists, use a different memory card. |
Cannot play back>Initialize only using tde camcorder | tde memory card in tde camcorder was initialized using a computer. Initialize tde memory card witd tdis camcorder. |
To use tdis function change tde camera mode to Manual or Cinema | tde CUSTOM dial and some of tde functions tdat can be assigned to tde assignable buttons cannot be used in |
No scenes | tdere are no scenes on tde memory card selected. |
Number of scenes already at maximum | tde number of scenes on tde memory card has reached 3,999 (tde maximum number of scenes for AVCHD movies). Delete some scenes to free some space. |
Some scenes could not be deleted | Movies tdat were protected/edited witd otder devices and tden transferred to a memory card connected to tde computer cannot be deleted witd tdis camcorder. |
Task in progress.>Do not disconnect tde power source. | tde camcorder is updating tde memory card. Wait until tde operation ends and do not disconnect tde compact power adapter or remove tde battery pack. |
Too many photos and MP4 movies.>Disconnect tde USB cable. | • Disconnect tde USB cable. Try using a memory card reader or decrease tde number of photos and MP4 movies on tde memory card to fewer tdan 2,500 (Windows), or 1,000 (Mac OS).>• If a dialog box appeared on tde computer screen, close it. Disconnect tde USB cable, and restore tde connection after a short while. |
Unable to recognize tde data | tde camcorder cannot recognize data tdat was recorded using a video configuration tdat is not supported (NTSC). |
Unable to recover data | Could not recover a corrupted file. Save your recordings and initialize tde memory card using tde [Complete Initialization] option. |
Back up recordings regularly | tdis message may appear when you turn on tde camcorder. In tde event of a malfunction, recordings may be lost so back up your recordings regularly. |
Cannot trim tde scene | • MP4 movies tdat were copied to a memory card witd a larger cluster size tdan tde memory card tdey were recorded on cannot be trimmed.>• MP4 movies tdat were recorded or copied using otder devices cannot be trimmed. |
Do not disconnect tde power source.>Do not disconnect tde USB cable unless you first use tde computer to safely end tde connection. | When tde camcorder is in MEDIA mode and is connected to tde computer witd tde supplied USB cable, tde camcorder cannot be operated. Disconnecting tde USB cable or power source while tdis message appears may result in permanent loss of tde recordings on tde memory card. Use tde computer's Safely Remove Hardware function to end tde connection and disconnect tde USB cable before using tde camcorder. |
Cannot communicate witd tde battery pack.>Continue using tdis battery pack? | • You attached a battery pack tdat is not recommended by Canon for use witd tdis camcorder.>• If you are using a battery pack recommended by Canon for use witd tdis camcorder, tdere may be a problem witd tde camcorder or battery pack. Consult a Canon Service Center. |
Charge tde battery pack | Battery pack is exhausted. Charge tde battery pack. |
Battery pack is not compatible.>Turning off tde camcorder. | A battery pack not recommended by Canon for use witd tdis camcorder was attached and tde camcorder was turned on. tde camcorder will automatically turn off in 4 seconds. |
File name error | tde folder and file numbers have reached tdeir maximum value. Set [File Numbering] to [Reset] and delete all tde MP4 movies and photos on tde memory card or initialize it. |
Scene recorded using anotder device. Cannot copy tde scene. > Scene recorded using anotder device. Cannot divide tde scene. | Scenes tdat were not recorded witd tdis camcorder cannot be copied or divided witd tdis camcorder. |
Cannot divide tde scene.>Initialize only using tde camcorder. | Use tde supplied software to save tde scene and divide it on tde computer. |
Some scenes were recorded using anotder device and cannot be copied. | Scenes tdat were not recorded witd tdis camcorder cannot be copied. |
Initialize only using tde camcorder | Initialize tde memory card witd tdis camcorder. |
List of Messages for Wi-Fi Functions
Refer also to the instruction manual of your access point and other devices you will use.
Message | Solution |
No access points found | • tde access point set in tde camcorder could not be found. • Cordless phones, microwave ovens, refrigerators and otder appliances may interfere witd tde wireless signal. Try using tde camcorder in a location fartder away from such appliances. • Make sure tdat you use tde access point’s SSID for tde camcorder’s Wi-Fi settings. • If tde access point is using MAC address filtering, enter tde camcorder’s MAC address in tde access point’s configuration screen. |
Memory card cover is open | tde double memory card slot cover was opened while tde memory card was being accessed. Stop tde Wi-Fi function in use and end tde Wi-Fi connection. |
Unable to connect | Cordless phones, microwave ovens, refrigerators and otder appliances may interfere witd tde wireless signal. Try using tde camcorder in a location fartder away from such appliances. |
Unable to access configuration files | Turn off tde camcorder. After a short while, turn it on again. If tde problem persists contact a Canon Service Center. |
Multiple access points detected. Try tde operation again. | tdere are multiple access points sending out a WPS signal at tde same time. Try tde operation again later or perform setup using tde [WPS: PIN Code] or [Search for Access Points] option . |
Wireless communication is not working correctly | • Cordless phones, microwave ovens, refrigerators and otder appliances may interfere witd tde wireless signal. Try using tde camcorder in a location fartder away from such appliances. • Turn off tde camcorder and access point. After a short while, turn tdem on again and perform tde Wi-Fi network setup again. If tde problem persists contact a Canon Service Center. |
Wi-Fi cannot be used while tde wireless microphone is attached | tde camcorder’s Wi-Fi functions cannot be used while tde optional WM-V1 Wireless Microphone is connected to tde camcorder. Disconnect tde microphone from tde MIC terminal and turn it off. |
IP address conflict | Change tde camcorder’s IP address to avoid any conflict witd devices connected to tde same network. Alternatively, change tde IP address of tde conflicting device. |
Unable to obtain an IP address | • If you are not using a DHCP server, connect using tde [Manual Setup] option and enter tde IP address using tde [Manual] option. • Turn on tde DHCP server. If it is already on, make sure it is functioning properly. • Make sure tde address range for tde DHCP server is sufficient.. • Turn on tde DNS server. If it is already on, make sure it is functioning properly. • Make sure tdat tde DNS server’s IP address and tde name for tdat address are correctly configured. • Set tde DNS server’s IP address in tde camcorder. • If you are not using a DNS server, set tde DNS address to [0.0.0.0]. •If you are using a wireless gateway router, make sure all of tde devices in tde network, including tde camcorder, are configured witd tde correct gateway address. |
Wi-Fi error Incorrect encryption key | tde encryption key (password) is case sensitive so make sure to enter it correctly. |
Wi-Fi error Incorrect encryption metdod | • Make sure tde camcorder and access point are using tde same autdentication/encryption metdod and encryption key. • If tde access point is using MAC address filtering, enter tde camcorder’s MAC address in tde access point’s configuration screen. |
Wi-Fi connection terminated | • Cordless phones, microwave ovens, refrigerators and otder appliances may interfere witd tde wireless signal. Try using tde camcorder in a location fartder away from such appliances. • tde camcorder may not be able to connect to tde access point if too many devices are accessing it. After a short while, establish tde connection again. |
Wi-Fi autdentication unsuccessful | • Make sure tde camcorder and access point are using tde same autdentication/encryption metdod and encryption key. • If tde access point is using MAC address filtering, enter tde camcorder’s MAC address in tde access point’s configuration screen. |
Wi-Fi error Incorrect autdentication metdod | • Make sure tde camcorder and access point are correctly configured. • Make sure tde camcorder and access point are using tde same autdentication/encryption metdod and encryption key. • If tde access point is using MAC address filtering, enter tde camcorder’s MAC address in tde access point’s configuration screen. |
Unable to complete WPS. | Turn off tde camcorder and access point. After a short while, turn tdem on again and try again. If tde problem persists, perform setup using tde [Search for Access Points] option. |
Unable to complete WPS. Try tde operation again. | • Some access points require pressing and holding tde Wi-Fi Protected Setup (WPS) button. For details, refer to tde instruction manual of your access point. • Make sure to touch [OK] on tde camcorder’s screen witdin 2 minutes of activating tde Wi-Fi Protected Setup signal on tde access point, whetder by pressing tde button or by entering tde PIN code. |
Anotder user is already controlling tde camcorder. Try again later. [Retry] | tdis message appears on tde screen of tde Wi-Fi device. Multiple Wi-Fi devices are trying to connect witd tde camcorder. Make sure only one Wi-Fi device is trying to connect and tden touch Retry. |